|
29/06/2010
dukepapas (46%)
shaft for this motor?
|
|
|
 |
|
|
 |
|
14/09/2009
diverdon (39%)
What is the biggest diameter prop you can use with this motor ?? Please .. I would like to use a 11 or 12 in to get the power without the speed ?? Yes ???
Thank You for the help . Don J.
|
|
|
| |
|
clipper
(40%)
you might beable to use two LIPOs to spin a 11 or 12 low pitch prop
|
|
|
|
Was this the best answer? YES | NO
|
|
|
|
|
|
|
|
10/09/2009
jdk1man (84%)
Are the bearings on this motor permanently lubed, or do they need to be oiled periodically?
|
|
|
|
|
|
|
|
|
5/09/2009
clipper (40%)
what motor mount is everyone using with this motor?
|
|
|
| |
|
clipper
(40%)
Has anyone measured the hole spacing? I measured 16mm in one direction and 18.5mm in the other, through the center.
|
|
|
|
Was this the best answer? YES | NO
|
|
|
|
|
|
|
21/06/2009
GeeBeeY (39%)
I can not find a shaft to replace for the Turnigy2836 Brushless Outrunner 1000kv on hobby king site. maybe I didn't look well.
Is there some one to give me the reference number of this piece.
|
|
|
|
|
|
|
|
|
5/05/2009
GeeBeeY (39%)
Is it possible to move the shaft of the Turnigy2836 the other side of the motor?
|
|
|
| |
|
touch n go
(81%)
yes its possible. loosen the set screw, use a mallet and lightly knock on the shaft and it'll move slowly to the other site. use the collar and set screw to tighten back.
|
|
|
|
Was this the best answer? YES | NO
|
|
| |
|
GeeBeeY
(39%)
I did what you say but the shat didn't want to move. Look like it is glued or very tight. I'm afraid to knock too hard and bend the shaft.
|
|
|
|
Was this the best answer? YES | NO
|
|
| |
|
davidoff
(77%)
Use vice and be gentle.
|
|
|
|
Was this the best answer? YES | NO
|
|
| |
|
GeeBeeY
(39%)
Thank you, I finally succeed.
|
|
|
|
Was this the best answer? YES | NO
|
|
| |
|
ay6810
(55%)
Hi guys, i tried the same thing-reverse the shaft but broke 2 magnets on the outer shell. I put it back together and it turns jerkily initially but smoothens out. Can I still use it? Is there any permanent damage?
|
|
|
|
Was this the best answer? YES | NO
|
|
| |
|
clipper
(40%)
Naxt time, remove the core first. When its time to put it back together, wrap a couple of layers of paper on the armature to keep it centered.
|
|
|
|
Was this the best answer? YES | NO
|
|
|
|
|
|
|
30/04/2009
hisky3D (67%)
how to reverse the shaft?
|
|
|
|
|
|
|
|
johnkim100530 (81%)
What is the maximum current (amp.)
and constant current?
|
|
|
| |
|
Dr. Katana
(90%)
Max. efficient current 20A - 25A
Current capacity 28A/20S
Data sheet URL, ***********hobbycity****/hobbycity/store/uploads/TURNIGY_BR_Series.zip
|
|
|
|
Was this the best answer? YES | NO
|
|
|
|
|
|
