|
28/05/2010
Ednac (66%)
What is the mounting hole size and spacing.
|
|
|
 |
|
|
 |
|
|
11/03/2010
ngashok (52%)
Hi ppl. Please help. While soldering I damaged the small connector given for the ESC with this motor.
Can anyone tell where to get a new one.
I do not know the name of that connector also.
|
|
|
| |
|
Bikalho
(59%)
You can use a 0,8mm bullet connector on this motor. I dont know the name of the stock connector.
|
|
|
|
Was this the best answer? YES | NO
|
|
|
|
|
|
|
|
29/09/2009
ngashok (52%)
Hello ppl. My AUW with my biplane came to about 200grams. Can someone tell whether it would takeoff with this motor 6*4 prop??
|
|
|
| |
|
Sachin
(57%)
no you should use 7*4 / 7*5 propler. It will fly but slower with those proplers also.
|
|
|
|
Was this the best answer? YES | NO
|
|
|
|
|
|
|
|
20/08/2009
elad (46%)
somebody knows where i can find bands for this motor ???
|
|
|
| |
|
maukabud
(52%)
o-rings in the plumbing dept. of your local hardware store!! I know that the small 4mm propsaver takes #7 size o-rings...this motor may take a size or two larger looks like. Experiment.
|
|
|
|
Was this the best answer? YES | NO
|
|
|
|
|
|
|
9/08/2009
maukabud (52%)
Anyone know if this motor would be a good replacement for the Techone mini-yak54 sold here on HC? Stock 7amp esc. I'm using Hyperion 25c 120mah 2cell batts. Original c-5 motor gets hot, mine burnt. Replaced it w/ a LCD killer bee from 2dogrc, but I think the kv is too low- 2000kv. Not quite enough power for hovering/3d. Not sure if I should replace it with another c-5, or this one.
|
|
|
|
|
|
|
|
|
10/07/2009
david in japan (-16%)
i am putting together a 120gram model. i have a JR 5gram receiver, 3 6gram micro servos, and now im looking for a motor and esc. i was thinking i want as much thrust as i can get with my 2s 300mah lipo battery. what combinations are people using? thanks ! david
robertson.david.campbell*gmail****
|
|
|
|
|
|
|
|
|
HYCRYPOTES (59%)
E' un ottimo motore, perfetto per micromodelli.
|
|
|
|
|
|
|
|
|
ishady (63%)
I use 2 of these (2 super simple 10A esc) for my mini TWINS weight 130gr, 3C 350mAH lipo, GWS pico rx, 2 3,7g servo.
http://www.youtube.com/watch?v=B0fufQwhwtI
http://www.youtube.com/watch?v=XJ8lb_UIc8c
|
|
|
| |
|
ishady
(63%)
Whopsie, wrong discussion...LOL
Sorry guyz.
|
|
|
|
Was this the best answer? YES | NO
|
|
|
|
|
|
|
|
ste92 (50%)
is this motor suitable for micro 3D models? have anyone tested this motor with a 5x3?
|
|
|
| |
|
Bluebird
(57%)
This is a nice running motor w/ GWS 5x3 & small 2s LiPo. I don't have any test specs but pulls homebrew 113 gram, 24" WS model just fine. Now that HC has dropped the price on the 10g. 1811-2000, it's the better deal IMO.
|
|
|
|
Was this the best answer? YES | NO
|
|
| |
|
ste92
(50%)
Thank you!
|
|
|
|
Was this the best answer? YES | NO
|
|
|
|
|
|
|
|
Marcos (36%)
I would like to know the total length of the engine, the diameter of the engine, the length of the shaft and the diameter of the shaft
|
|
|
|
|
|
|
|
|
Marcos (36%)
I would like to know the total length of the engine, the diameter of the engine, the length of the shaft
|
|
|
|
|
|
|
|
|
Marcos (36%)
I would like to know the total length of the engine, the diameter of the engine, the length of the shaft
|
|
|
| |
|
tronchaviones
(87%)
My unit is slightly different from the photo (shorter, fully cylindrical shaft).
Total lenght (from firewall to top of shaft) 21.5mm, diameter 17.5mm, shaft length 3mm.
The concentric cylinders around the shaft will tightly fit 4, 3 and 2 mm shaft holes.
The mounting holes are 1.5mm wide, 21mm apart.
Mar 11, 2009
|
|
|
|
Was this the best answer? YES | NO
|
|
|
|
|
|
|
| |
|
Michel
(50%)
Yes, on a F22 90gram. Prop 5x3 10800rpm.
Enough thrust.Good motor.
|
|
|
|
Was this the best answer? YES | NO
|
|
| |
|
vinc29
(70%)
I use it on a small custom model, 110g with 6030, 6A ESC and 2S360mah rhino. Very good motor from 8minutes of flight at full power to 14minutes at half.
I also use it on a biplan bimotor of 180g, with 2S900mah and 6030 prop. about 17minutes at 60%
photos: ***********iroiserc****/forum/viewtopic.php?f=22&t=557
|
|
|
|
Was this the best answer? YES | NO
|
|
|
|
|
|
|
|
Stephane (46%)
It's written "shaft 2mm" under the picture
|
|
|
| |
|
Alberto
(80%)
Thanks. Did not noticed it the first time
|
|
|
|
Was this the best answer? YES | NO
|
|
|
|
|
|
|
|
Alberto (80%)
What is the shaft size? I am looking for a correct prop. adapter
|
|
|
| |
|
tronchaviones
(87%)
The concentric cylinders around the shaft will tightly fit 4, 3 and 2 mm shaft holes.
Mar 11, 2009
|
|
|
|
Was this the best answer? YES | NO
|
|
|
|
|
|
.jpg)
