|
|
|
|
I bought 2 of these motors for the 55mm fans in my F-14 tomcat (tomcat blog)
Here are the measured motorparameters which you can use in www.peakeff.com to see motor performance and efficiency :
HXT 2435 - 4400kv nr1 :
Rm = 75mOhm
Io = 1.6A
V = 11.4V
RPM = 49400
kv = 4333
HXT 2435 - 4400kv nr2 :
Rm = 70mOhm
Io = 2.4A
V = 11.4V
RPM = 53763
Kv = 4716
45 people like this review.
|
|
|
| I put this in my 1/18 Vendetta ST, and it has the perfect blend of torque and speed while running on 2 cell LiPo. Using 3 cell would be insane. Very happy with this motor!!!!
24 people like this review.
|
|
|
Nice motor with big cooling holes.
Shaft is indeed 2mm in stead of the advertised 3mm, so be aware !
This motor is well suited for the 55mm EDF 6 blade that UH sells. The motor fits the fan and adaptor perfectly. On 3s lipo it draws 17A WOT and produces 370g of thrust with the 55mm 6 blade EDF.
20 people like this review.
|
|
|
This one fits perfectly in the GWS EDF 55 system and boosts my GWS A10 to where it should be.
Absolutly no frickeling, fits exactly even the screws delivered with the GWS Fans fit! Pulls 21,3 A and gives 203 Watt with the 55 Fan!!!
Great value for the price!
15 people like this review.
|
|
|
| Perfect fit for GWS 64mm fans,shoehorn 1 of these motors and 64mm fan into the Freewing L-39 on 4 cells,just don't forget to pull the bang seat pin before you fly!!!!exciting to say the least!!
12 people like this review.
|
|
|
| Nicely machined up motor (marked Turnigy brand)and power is as expected on my EDF, let down however because motor turns rough as there is a lot of bits of metal stuck on the rotor magnet. Tired cleaning it out without disassembly without any luck. I've heard of this complaint before too......
10 people like this review.
|
|
|
| This is a longer term test with this motor. I have been running it in my Vendetta ST, and been getting really awesome results. With a 11/45 gearing, while running 2 cell lipo and a mamba 25 ESC, i have radar it at 27mph, and with a 16/45 gearing, it radared a constant 34mph. The motor ran rather cool in both set ups, measuring a 125-135 degree F. Over all i am very impressed with this motor, so impressed i bought another two more!!!! And would HIGHLY recommend them to anyone with a 1/18 scale rc car.
9 people like this review.
|
|
|
| Great fit for my mini-inferno. Has the torque to move a heavier car, yet produces wonderful top speed. The little brushless' at your local shop have a hard time moving a 2+lb truck around. And, for the price... fagittaboutit! Oh yeah, these guys are fast express air in like three days and it's still cheaper then any mini motors in the mags!
8 people like this review.
|
|
|
| Placed it into my Mini-Inferno, now its really fast and the acceleration is just as well perfect! In combination with a HXT D9 G2 1700mAh and a TowerPro 25A Brushless Speed Controller its a awesome package.
8 people like this review.
|
|
|
| GREAT MOTOR FOR 64EDF GWS HC SELLS!!!!!!!!!!!!!
7 people like this review.
|
|
|
Use this in my Great Planes L-39.
In the stock Hyperflow Unit it draws about 26 Amps on the ground and produces plenty of thrust. Totally recommended :)
6 people like this review.
|
|
|
| these motors worked very well for what i wanted to use them for ( a gws me-262 ducted fan) they have more than enough power, only fault i can find really isn't really a problem but it would be easier for 1st timers to figure things out, what i am talking about would be the connecters on the motor, while they come premounted as shown in the picture it would be nice if the required connecters that mount to the speed controller were included so the motor and speed controller could be connected with only having to install the parts on the speed controller and not spend time looking to find parts that would work with what was just included with the motor only, also including the little screws with washers for putting the motor to what ever mount your putting it in would be nice, save the aggrivation of trying to find the right size and wondering what length to get.
6 people like this review.
|
|
|
| This motor is a perfect fit and performer in a Losi Mini LST. Used with stock pinion and the mini-t slipper conversion this baby on a 3s LiPo gets no hotter then 130degrees after 30mins with no heatsink and gets at least 30-35mph with insane torque which for a 1/18 truck is plenty fast. Again a perfect motor, great performer and excellent price even after shipping to the states.
5 people like this review.
|
|
|
I have two of these motors installed in a Nitro Planes A-10 with a 55MM GWS fan rotor. On a 3S LiPO battery they pull about 25 amps each producing about 250 watts.
They fit perfectly into the 24.2mm housing on the fan units pre-installed on this model. The mounting holes lined up but I had to trim the tabs slightly to accommodate the required shaft adapter for the GWS fan rotors.
Overall a very good motor for the price.
5 people like this review.
|
|
|
perfect motor for multiplex micro jet.
lot of speed :-)))
3s 2200, prop 4x3. need lots of air for cooling
easy replacement for speed 400
cons.: the axel is thin, and bendts esay
4 people like this review.
|
|
|
| Beware - The shaft is advertised as a 3mm shaft when it is actually a 2mm shaft. I was very disappointed.
4 people like this review.
|
|
|
| Excellent power for 54-56 mm dia. ducted fans using 3 cell Lipo's with 45 amp speed controler. You could use a 35 amp if you wanted to. Lots of power, and reliable. Keep the Speed controller vented, and you won't have any trouble with these motors or speed controlers. I have many flights with these motors, and no trouble. They're strong! Very satisfied.
4 people like this review.
|
|
|
Overall a good quality motor. I bought this to replace a motor for my Hyperflow fan. Well the only downside here is the 2mm shaft which is not stout enough for a high spinning EDF. I would make this shaft a minimum 2.3mm or even better 3mm!!!
3 people like this review.
|
|
|
Coupled with the EDF Ducted Fan Unit 6 Blade 2.17inch from here it draws 14A at full throttle with a zippy 2200mA 3S. Only drawback is the lack of 3mm diameter mounting screws.
3 people like this review.
|
|
|
| Insane!!! direct fit in a mini lst, on 1500mah 3s and 18t pinion will do a standing backflip, unrelentless torque and more than you'd ever need top speed in a mini, buying another for my other lst. high quality good price what more can you ask for!
3 people like this review.
|
| Click here to see all reviews |
5 crowns 
