|
8/08/2010
bob (72%)
what will this work on?
|
|
|
| |
|
stuman1995
(78%)
it will power any thing not over the allowed voltagae
|
|
|
|
Was this the best answer? YES | NO
|
|
 |
|
|
 |
|
11/07/2010
dori1 (75%)
is this ubec linar?
|
|
|
| |
|
Alan
(100%)
If is doesn't say SBEC, then it most likely is a linear regulator. SBEC is the switching regulator.
|
|
|
|
Was this the best answer? YES | NO
|
|
|
|
|
|
|
10/09/2009
Bandit (81%)
I read in reviews that jamper in the left side it has 6,22V and in the right side it has 5,27V, this correct one?
|
|
|
|
|
|
|
|
|
10/09/2009
Bandit (81%)
Somebody found or knows where it has the operation manual?
|
|
|
|
|
|
|
|
|
30/07/2009
Mauricio (46%)
Will this UBEC handle 5 high torque HD-9150 servos plus 2 standard servos plus spektrum AR7000 receiver?
|
|
|
|
|
|
|
|
|
pasodoble (79%)
What are the dimensions of it?
|
|
|
| |
|
Ericsson
(50%)
and weight?
|
|
|
|
Was this the best answer? YES | NO
|
|
|
|
|
|
|
|
killbill (57%)
How works the jumper ?
Thank you
|
|
|
|
|
|
|
|
|
David (46%)
I need the instructions for the 4A UBECw/low voltage alarm.
THANKS
|
|
|
| |
|
George E
(54%)
LOL... you and me too. No directions I do understand when using a ubec. You cut or unplug the red wire from the speed controller that pugs into the reciever (the plug that has 3 wires) My question is about the jumper... how do you know if its set for 5 volt or 6 volt don't want to toast anything. =( guess I might have to get some tools out and do surgry i know some are marked on the board, but the heat srink is not clear..its yellow.
|
|
|
|
Was this the best answer? YES | NO
|
|
| |
|
davidpc2
(47%)
Hi George E, maybe sounds stupid but can try a voltmeter, maybe it works.
|
|
|
|
Was this the best answer? YES | NO
|
|
|
|
|
|
|
W3FJW Ron (42%)
What is the use of the ckt board that everyone cuts out and how is it done??
|
|
|
| |
|
waynemia
(74%)
The additional board makes it easier to mount the regulator. You can cut if off if not needed.
|
|
|
|
Was this the best answer? YES | NO
|
|
|
|
|
|
|
|
Nigel (43%)
Just bought one of these. When I plug it into 3 cell lipo the alarm just goes off and it doen't work. Can anyone advise me what I am doing wrong
|
|
|
| |
|
waynemia
(74%)
The alarm only sounds for voltage drop below 6Vdc. The alarm was designed for 2S LiPo.
|
|
|
|
Was this the best answer? YES | NO
|
|
| |
|
Nigel
(43%)
I use a 2S fully charged but there was obviousely a defect. I ripped the alarm off and it works fine now.
|
|
|
|
Was this the best answer? YES | NO
|
|
| |
|
ronchudy
(67%)
soldered this ubec to a hobbycity simple esc battery leads, red to red black to black ., cut the red wire on the esc , connected the ubec to the aux channel on my reciever and fired it up. didnt program the esc but it worked nicely.happy so far.
|
|
|
|
Was this the best answer? YES | NO
|
|
| |
|
ronchudy
(67%)
soldered this ubec to a hobbycity simple esc battery leads, red to red black to black ., cut the red wire on the esc , connected the ubec to the aux channel on my reciever and fired it up. didnt program the esc but it worked nicely.happy so far.
|
|
|
|
Was this the best answer? YES | NO
|
|
| |
|
bero
(83%)
weight?
|
|
|
|
Was this the best answer? YES | NO
|
|
|
|
|
|
