|
12/08/2010
ian141 (75%)
Does anyone know how many turns and gauge of wire are on the stator?
|
|
|
 |
|
|
 |
|
17/12/2009
Flyhigh (60%)
Has anyone tried this motor with 4S Lipo?
|
|
|
| |
|
Barndog
(42%)
It will burn it up.
|
|
|
|
Was this the best answer? YES | NO
|
|
| |
|
Ashley
(29%)
hi i use this with a 2s an sometimes a 3s lipo an it works fine i think 4s will burn it out though
|
|
|
|
Was this the best answer? YES | NO
|
|
|
|
|
|
|
13/09/2009
Magnus (70%)
Hi!
Bougth this motor with
- hexTronik PRO 10A BESC w/ PC Programmability
- GWS HD8040 3 Blade Prop Counter Rotate (2pc)
Meassured the trust today, and the scale said 50g and 5600 as max rpm (24 magnet motor poles[don't know the correct setting for this motor])
This can't be correct! Whats wrong
Regards Magnus T
|
|
|
| |
|
Magnus
(70%)
3s battery
|
|
|
|
Was this the best answer? YES | NO
|
|
| |
|
Derku
(80%)
I tested the 1300kv with GWS HS8040 3 Blade on 2s and it gives a peak of approximately 220 grams at 3.9A.
|
|
|
|
Was this the best answer? YES | NO
|
|
| |
|
Ikarus 99
(37%)
When i read your message right you bought counter rotate props.One is spinning left and the second one is spinning right.Maybe you got the wrong prop.Take the second one and meassured again.
|
|
|
|
Was this the best answer? YES | NO
|
|
|
|
|
|
|
|
5/09/2009
Cid156 (94%)
Did the quality of the bearing changed?
On my new one, the bearings seems differents from the old one and they were damage on the first hard landing.
It would be great if Hc can offer bearing remplacement. It is more easy to break a bearing than a shaft
|
|
|
|
|
|
|
|
|
niels (71%)
Hi, most people think that, i made vid of the prob : *******nl.youtube****/watch?v=MxIa95Z2O8w
I don't have an other BL esc...
(niels-coolen*hotmail****)
niels
|
|
|
|
|
|
|
|
|
niels (71%)
hi,
i bought this motor, but have a prob with it...
When i give gas the motor doesn't want to turn, but if i give it a little help tu turn ( like by gas planes) it will turn...
anyone know's what my problem is ?
|
|
|
| |
|
Dreamcatcher
(64%)
Hi,
I think it might be a misconfiguration of your ESC.
(wrong start or timing mode ?)
do you have tested your brushless with another one ?
regards
|
|
|
|
Was this the best answer? YES | NO
|
|
| |
|
Eric1180
(-53%)
I have the same issue with a 10Gram motor. I changed ESC and for the most part problem solved. I will some times hesitate.
|
|
|
|
Was this the best answer? YES | NO
|
|
|
|
|
|
|
|
Andre (62%)
It says the motor comes with mount and prop saver, I would like to know what they look like, if somebody could point me to some photos?
|
|
|
| |
|
Vidar
(73%)
Here's the mount (although the mount now comes with 4 "legs" instead of 3): ***********hobbycity****/hobbycity/store/uh_viewItem.asp?idProduct=5217
and here's the propsaver: ***********hobbycity****/hobbycity/store/uh_viewItem.asp?idProduct=3738
|
|
|
|
Was this the best answer? YES | NO
|
|
|
|
|
|
|
|
Sterling (57%)
can anyone tell me what size the set screws are on the side of this motor? One of mine came out during flight.
Thanks, Sterling
|
|
|
| |
|
martseger63
(78%)
They're M3, dunno the length, but that's not so critical 3-5mm should be just fine!
|
|
|
|
Was this the best answer? YES | NO
|
|
|
|
|
|
.jpg)
.jpg){kind=small}
