HobbyKing Online R/C Hobby Store : Turnigy highrate 30FPS Ultra-small Digital Camera W/ 2GB SanDisk Micro SD

View all comments | (123 threads)

Ask a question

27/08/2010
c_dos (28%)
Wich is better this or the turnigy grey cam?

Thank you.

21/08/2010
Gordon76 (100%)
21/8/10
Desperate Dan
I'm using Windows XP Home and it will not recognise my camera. The first time I hook up all ok* second time, nothing and nothing since. Anybody had similar problem and how was it fixed. I'm think of returning it for replacement

10/08/2010
Mats S (72%)
Hi all, Got my camera today and after a 3 hour charging I thought I’d try it out. Turned on the camera and nothing, what?? I thought. Ok, nothing more with that, tried to push some buttons… The red led flashed once each time I pressed to Mode button. When pressing the “start/stop” button nothing happened at all any time. Looked at the instructions listed here under the files tab, in the discussion area, review area and in the community area, nothing still.. Plugged the damn thing back in to the computer and formatted the SD card, read somewhere that it could help, nope, not for me. Plugging it back and forth a couple of times and suddenly it records a couple of seconds of video and then stops and leds go out, tried to press the mode button but only one flash and darkness. Anyone else who have had similar issues and got their camera to work?

23/07/2010
Kerosene (100%)
My camera is dropping frames with the *new improved* SanDisk Fast spec SD Card. Is it worth buying a decent RETAIL class 4 card for this camera... will it solve the dropped frames problem? Other than the dropped frames, I'm very happy with the image quality.

Junior (-20%)
im too

22/07/2010
Old Man (72%)
How do i know when its fully charged via USB. I just got one of these and i only get red & blue on constant when pluged in. on/off makes no difference. have not seen yellow or green at any stage in any mode as stated in manual downloaded from this site. But it does work well on video on the short tests i have given it

tom tom (-292%)
Check the voltage before & after with volt-meter:batt.should get warm if charging O K. Never let batt. get "hot"Tom Tom

Junior (-20%)
dont know

BatusaiX (88%)
Started charging since last night, 12hours now and it's red & blue. Still charging, will do a 16 hour charge & see if there are changes on the led color.

BatusaiX (88%)
***Update No changes on the led colors. Could be there is no led to determine a full charge. I just did a 14 hour charge. I unplugged it when I felt battery was getting warm. In hindsight, I think it would be best to have an initial charge of 6 hours. You get to charge it time & again when you need to figure out the camera.

22/07/2010
JOU (35%)
Where can I find the drivers to use the TURNIGY CAMERA as webcam? My PC has Windows VISTA.
Thanks.-

ipin17_aero (63%)
http://www.hobbyking.com/hobbyking/store/uploads/376563753X21536X12.zip

Junior (-20%)
on forum

fordfm (46%)
find flycam drivers. It compatibility with this camera.

21/07/2010
Martin. (40%)
My date/time disappeared while my memory card got damaged (or just because of the damaged card). Anyhow I replaced the card, but the date/time is no longer visible when making a picture/movie. Is it possible to get it back? Thanks for any suggestions.

17/07/2010
jabio (84%)
Una gran cmara, alejar de variador y motor para evitar interferencias en la imagen.

Muy Bien...

16/07/2010
luiscbr (82%)
Hi
Somebody help me set the time tried and failed, where this file should I change, I created one but I do not know where to put. Thanks Luis

12/07/2010
ktaylor (81%)
Have you ran into an issue where the cam shuts off for periods when you're filming? I noticed that there were two periods, one where the cam stopped filming for 2 minutes & then again later on for 50 seconds. I had noticed it before but haven't been able to figure it out. Sometimes it films just fine & will go for a full flight worth. Am I putting it into some kind of sound activated mode?

Hrubster (77%)
The storage disk is too slow. Need to upgrade to a faster media. It stops to record the pictures to the media because it can't do it on the fly.

RC_SCHU (84%)
I can only get ~ 2 minutes at a time on a flight.I'll start the camera and then on reviewing flight it will be in three or four segments. I push mode button twicew and then start button once. This gives me a red and a blue led.

9/07/2010
tullio (67%)
Can I remove the date? If I change TAG file with a file empty is right?
Thanks

9/07/2010
Enkay (72%)
How do you reduce the file size. The camera worked well but a 7 minute video as an .avi file was 350Mb

exetion (43%)
Use the best edit program-Camtasia Studio 7, it can reduce the file size tremendesly.
And even a reguler Windows Media Player Can Reduce the file size.

ipin17_aero (63%)
you can use video compression/converter software to reduce the size

Enkay (72%)
Thanks for the help. I have now downloaded free versions of "Format Factory" and "Videopad" and can convert file types and save in new formats. This reduces the file sizes

10/06/2010
jaank (67%)
If i do like i allways do (on, 2X M, and shutter) and the blue light doesn't work and it doesnt record. What to do?

fordfm (46%)
On my chamber the mode indicator too does not work, simply consider the pressing, one pressing of the button mode translates the chamber in a mode of record of video.

19/05/2010
BearPaw (42%)
Hobbyking,
when you are going to have something like this (www(dot)aeeusa(dot)com/en/productshow(dot)asp?Sendid=60)? It would be great for boats and other water sports. Greetings.

17/05/2010
alexfc22 (37%)
How change card in tr52dv?

I change for a kingstone of 8GB but tha camera not recognized the card

thanks

audriusv (58%)
Hi, I think it is limited to 4GB Micro SD cards only.

pippo65 (18%)
My units works well with 8Gb HD class 4 Kingston card! only led doesn't work, only one color light for all kinds of recording... mah!

alexfc22 (37%)
in description say: Capacity of memory card: Can support upto 16GB (max.)

:s

15/05/2010
Ebiker (9%)
I've deleted DCIM folder by mistake and now the cam won't record and when plugged to USB it doesn't come up on PC either. So now I can't acces the memory card to try to format it. Anyone has an idea what the problem is? Thanks

audriusv (58%)
Try to put it some digital photo camera (with adapter to SD size) and format it. Maybe photo camera will recreate folders for you. It could be some file system corruption on card.

Ebiker (9%)
Thanks! I've figured it out now. Nothing worked so that I took the card out and shorted the contacts in *ast hope it'll reset. Strangely it worked and is as god as new again.

pippo65 (18%)
maybe you can use adapter micro-sd to sd, or usb-micro sd directly on pc... or you can use in photo cam or phone cell, they make new dir dcim, all nikon does it...and after reuse it on turnigy camera

kimce (72%)
It creates the folder automatically, thats not the problem. What you need to do is to try to repair the card via card-reader. And when you format, it must be fat16, not 32 (as I remember). I accidentally got it into same situation and it started to work after formatting to the oldest possible format.. I went to by larger card and the reader, which costs twice the price of the camera :D

12/05/2010
xadam (84%)
Can I disable date/time line in video?

Flatstrap (39%)
I just got one and it does pretty good video in the daylight, not so good in low light. My lens is a little off square as well.
Some notes...
++The red led flashes when charging on the USB, this takes about an hour or so.
++There is only a Red and Blue led
++The time stamp cannot be removed.
++Records in 740x480 which fills the 2Gig card in about 40 minutes.
++If the card fills up the file is saved and recording stops.
++My battery lasts about 50 minutes.
++If the battery runs out the file is not saved and you end up with two other files on the disk called AAAAAAAA.AAA and BBBBBBBB.BBB, just recharge the battery and delete those files.
++Also if the battery runs out the time will be reset back to it's default.

I hope this helps others out.
Regards Flatstrap (13 May 2010)

Flatstrap (39%)
No you cannot. The time stamp is fixed. :(

lbreciani (46%)
ainda nao descobri como fazer isto

Michael (72%)
the manual is available on the net ,type in 'md80 manual' as you will see this camera is released under different names

Firepower (32%)
Simple answer - No.

4/05/2010
Cole (74%)
Looks like the new one is an improvment

Ebiker (9%)
never had the old model, this one makes great quality videos but it is a pain to use having to keep switching from mode to mode.

TrubsNZ (41%)
They look different, but I'm sure they will be exactly the same camera.

1/05/2010
iansydbr (60%)
I received the camera a couple of days ago.Just a couple of questions that I hope somebody can answer.
(1)I can change time and date ok but if I leave the camera off for some time and then take a video time and date have changed.
(2) The camera works ok in voice activated mode but if selected to manual mode its intermittant in trying to get it to record.The 2 sets of instructions are different for this mode.
I always assume that Iam doing something wrong before faulting the unit so could somebody help me out. What Iam doing wrong.

Ebiker (9%)
yeah the time is useless, onece you turn the cam off it's back to default.
to record in normal mode press standby, mode, standby again, mode again and you get blue/red flashing meaning it's recording. manual is totally for something else I think :)

TrubsNZ (41%)
Hi, 1, I have never worried about changing the time and date, so cant comment here, (2) I always change it into manual mode for video recording, it can sometimes take two clicks on the mode button to get it into manual mode, but this seems to be the most reliable way to record..

27/04/2010
3lad3 (63%)
I see it says "Photo format: JPEG 1600x1200". Does this mean you can set it up to take regular photos, say one every 10 seconds or something?

Ebiker (9%)
it just take 1 photo when you press the button.

TrubsNZ (41%)
yes it does take photos, but not sure about automating it for time lapse. It is such a small lense, i cant imagine the photos to be very good.

25/04/2010
CQ_helis (87%)
Windows capture Driver:
*******podpora.wiapest.cz/kamerky/web_cam_driver/
***********mediafire****/file/htnuzwtmtyj/SPCA1528_V2220_MultiLan_090217.rar
***********rcgroups****/forums/showatt.php?attachmentid=2896566
*******narod.ru/disk/17181438000/SPCA1528_V2220_MultiLan_090217.exe.zip.htm

The1CZ (64%)
very nice THX

22/04/2010
TigerAce (63%)
I am having some problem with the date, it stats back from Jan, 2008. I tried to change it by following the direction on the date files upload, but with no luck, I added the file to path for the camera DCIM -> 100MEDIA file, and I turned the camera off, unplug it and then conect it to the PC, but it is still show the same date (Jan. 1, 2008). Anybody could help me please, is their is a trick to doing it..??, other than that, the camera works just fine, I did a few movies, and it works good, the quality of the movies is OK, but for the price of the camera, that is a good deal. So lets see if we could fix the wrong date....!!, and help please...?? P.S. if you could insert the file with your reply, that would be helpfull, thanks.

Junior (-20%)
go to forum and find the problem

Ebiker (9%)
just forget the date is the best advice really.

waynemia (74%)
Place the file in the ROOT directory. Check the Files tab. There is an example file. Just download it, update the date and time, and save it to the root directory.

14/04/2010
jflessne (50%)
Anyone know were I can get a replacement battery? I've used it once. Since then it only shows LED's when it's plugged in so I suspect the lipo is bad.

13/04/2010
Mark (25%)
I must be stupid. How do you set the time and date on this camera? Some say do a time.txt file. Where do i write this? or can i turn the time off. It does my head in.

Halko (44%)
This new stock uses the tag.txt file.
File should look like this:
[date]
2010/04/15 12:12:56

Note that you have to write the [date].
Place the file root of the SD. Turn the cam off and then back on. File disappears and the datetime should be ok.

Junior (-20%)
i have the same problem

13/04/2010
Mark (25%)
Hey I need help. ust got my camera, wondering are there any instructions on using it. How to record. I know its stupid but please give me advice. thanks

Halko (44%)
Is the led always red? Maybe the camera still have same issues.

It should go like this. Put camera on. Wait couple seconds. Press M. Led color changes to blue. Pres rec and it starts record.

Mark (25%)
I turn it on. Press M. Led then turns on to red. Press rec and well led does not change so not sure if its recording. How can i tell? A blue slow flashing led. does that mean rec?

Halko (44%)
Yes, that means rec. But it seems that this new stock still has those issues that resent had. Good luck. I sent mine back.

Mark (25%)
Cheers. I was able to rec. Movie works fine. Think i will keep it for now. Thanks for your help. Do you know much about setting the time?

Junior (-20%)
just press the buttons

TrubsNZ (41%)
Easist way to record is by pressing the M button once so LED shows blue, then press the other button to start recording, the blue led will flash to show its recording. remember to stop recording press the other button again to stop. If you press the m button or switch it off while recording, you will lose the file

domdom (53%)
insert a mini-sd-card, charge, turn it on(red light constant), press the m-button, press the stop/record button maybe twice. then the red light stays constant and the blue light flashes. its recording. to turn it of, press the stop/record button again. easy. hope to help you with this

Michael (72%)
manual is available on line under 'md80 manual'.

1/04/2010
clipper (40%)
Has any one taken the camera apart to see if the lens/sensor assembly can be removed from the rest of the camera. I'm hopping, it will become really uesfull.

FusionTiger (71%)
I did, the lens is built into the sensor component and the component's connections are soldered onto the circuit board with a ribbon cable. The component is only attached to the housing by a little foam tape.

If you are wondering why I had opened it up, it was because the unit I recieved was faulty and technically killed the microSD.

miker1615 (56%)
The sensor is just fitted in the camera body but wired with ribbon cord to the board. Unless you are a micro circuit wiz, better forget it.

31/03/2010
Halko (44%)
Anyone received this new stock. Have the issues been resolved?

Eric1180 (-53%)
same question

miker1615 (56%)
Yes and No.

TrubsNZ (41%)
These work really well, no glitches at all. great little camera

27/03/2010
Thomas (63%)
Hi. I just purchased this camera, but have not received it yet. From reading the comments it seems like I will also need a higher speed memory card to get good video. Is this camera compatible with the micro SDHC format, or only the micro SD?

mirceacul (60%)
"*Now includes SanDisk Fast spec SD Card for smooth high rate video recording.
WARNING.
Always be sure that your camera includes a fast spec memory card. Cheap memory cards will not record smooth video. Our camera includes a SanDisk fast rate card.
Also be aware, the case of this camera is very common. Many factories produce the same style of camera but without a true 30FPS framerate. Our camera is true 30FPS! "

HK knows about the problems with the first memory cards and they corrected. You will receive it with high speed memory SanDisk

Abraham (20%)
I am using it with the Micro SD that came with it and the vid frames are clear without ANy dropped frames.

TrubsNZ (41%)
Problem is sorted now they send with a fast micro sd. not sure what SDHC is though sorry

Firepower (32%)
There is nothing wrong with the card that comes with it but any replacement ones you get have to be fast ones.

27/03/2010
skyroux (36%)
Hello, I'd like to know if this cam is better than the other turginy one sold in this website : http://www.hobbyking.com/hobbyking/store/uh_viewItem.asp?idProduct=10973&Product_Name=Turnigy_30FPS_Ultra-Mini_DigiCam_W/_2GB_SanDisk_Micro_SD ?

mirceacul (60%)
I have the one indicated by you and it's not real 30FPS. I saw you tube video filmed with this one and there seams to be way better then mine (see review there are some links there). I think this one is the much better deal!

miker1615 (56%)
It's not.

26/03/2010
Ben (63%)
What is the latest on the bugs? I have a Flycamone2 and out of approximately 30 flights, I was able to view 2 videos. There was always a corrupt file error message. So I'm looking for diferent cam. Please Help!

Abraham (20%)
I think this one is much better than the FCOne2. In both price and value

TrubsNZ (41%)
never had a problem with my turnigy cam, great colour, smooth video. easy operation

domdom (53%)
it always worked for me using the free VLC-player. some videos require its repair-function to create an avi-index. i didnt lose a single video. like it very much.

BCBasher (77%)
Only gkitch I botice are the timestamp hate it and if you switch the power off while in recording it corupts the file. Just remeber use the start/stop button.

BCBasher (77%)
And by krbord is brokem.

Firepower (32%)
This one usually work great and I have two of them and two more ordered.

24/03/2010
frwind (93%)
Good video capture.

miker1615 (56%)
I agree. Good when it works.

23/03/2010
Mark (25%)
Hey Guys, I want to buy a camera which one should i get. I have a electric and a gas plane should i buy 2 different ones or just one. What is the difference between this one and the Turnigy 30FPS Ultra-Mini DigiCam W/ 2GB SanDisk Micro SD to me they look the same. Please help!

This customer was awarded a credit for their answer.

Mark (25%)
Thanks I just put this one on order. Will post review when i use it

TrubsNZ (41%)
yeah they same as far as i can see, just buy one, buy a couple of small 90 degree brackets from a hardware store and zip tie it on, to view a bit I have recorded, look up "gliding pourerere" on youtube.

12/03/2010
Ebiker (9%)
Is there a way to stop the time from showing? Setting it is useless since it goes back to default on battery change. They do make good vids but sure have some strange issues. When I got mine, the video was on 30 degrees angle. I had to open it and set the lens straight and glue it in place because the wire strip was was pulling on the lens spinning it to side. Glue holds the lens in place but now the wire strip is under tension so I hope it all holds.

Halko (44%)
No there is not.

Fabio A. (63%)
My cam works fine at ground and corrupts some files when mounted on my plane flying. Does someone figured out what to do?

BCBasher (77%)
Check your battery tabs. Mine shut off from ***ps and vibration I tweaked the tabs out with a dental pick so the push harder problem solved. If you are not careful putting the battery in you can crush them down.

12/03/2010
Auber (50%)
Ver video: exelente s no consigo colocar a data certa, se alguem poder me ajudar agradeo.
Auber
http://www.youtube.com/watch?v=UOfJRJaGsSk
http://www.youtube.com/watch?v=5sUdWB9xxLc

11/03/2010
fmimages (56%)
I just made my 3rd video with this camera and am getting to know it. Take a look here: http://www.youtube.com/user/fmimages#p/a/u/0/be2v3TdD4Vo

Auber (50%)

www.youtube.com/watch?v=UOfJRJaGsSk

http://www.youtube.com/user/fmimages#p/a/u/0/be2v3TdD4Vo

6/03/2010
eezfly (59%)
where can I find the manual on hk ?

Edney (86%)
""http://www.hobbyking.com/hobbycity/store/uploads/hk52.zip""

4/03/2010
Bernd (72%)
"Reviews" do not work here, so I'm posting my experiences as a "question".

I used the TR52DV camera for outdoor flights with my Honey Bee CP helicopter.
Poblems encountered:
1. Low fps rate (far from 30 fps) plus vibration of a helicopter means you get blurred patterns and never a sharp video.
2. Narrow angle of the lens, so it sees only what is in direkt line. Cam has to be pointed forward to film more than the ground and see the horizon to be identified as a flight video at all. So you need to build an extra camera mount to use it on a helicopter.

Edney (86%)
The Manual and some software are in:

***********hobbycity****/hobbycity/store/uploads/hk52.zip

Edney (86%)
Manual location:
""http://www.hobbyking.com/hobbycity/store/uploads/hk52.zip""

TrubsNZ (41%)
never had any luck with supplied mount, i made one from an angled bracket in hardware stores, and i just zip tie it on there, lots less vibration. I get a pretty good field of vision, sounds like other people have found the lense inside camera not mounted properly, this might help

BCBasher (77%)
My brakets ar posterboard foam with neoprene tape lining lighter than metal and have some give to suck up vibration.

4/03/2010
RiMr71 (68%)
Hallo, have you samebody any idea how we can disable the Date and Time in the Video?
Because I am worry from this... :-(

Auber (50%)
veja meu video
http://www.youtube.com/watch?v=jt8MhmvoLaU

RiMr71 (68%)
Hmmm, video is OK, but it is not answer for my question... My question is, how I can disable timecode?

Halko (44%)
You can't disable it.

3/03/2010
Holzmichel (50%)
Hallo, ich bin wohl zu doof.
1. Um das Datum einzustellen habe ich das Text-File erstellt und mit Leer und Return die Zeilen gewechselt. Abgelegt im Stammverzeichnis. Leider ohne Funktion.
2. Eine Treiber CD fehlte. Hier auch nicht vorhanden. Der empfohlene Treiber STK02N 2.0 von der FCO2 bringt es leider auch nicht. jedes 2. Mal heist es: Unbekanntes Gert.
3. Die Funktion als PC-Kamera funktioniert auch nicht. Da soll beim Einschalten die Mode-Taste mit gedrckt werden um in den Photomodus mit roter Anzeige zu gelangen. Das klappt gar nicht. Ob mit oder ohne gedrckte Mode-Taste beim Einschalt immer die gleiche gelbrote Anzeige. Rot immer bei USB Verbindung, Gelb bei Akkustischem VideoStandby.

Was luft da falsch?

Holzmichel (50%)
Help,
No Cam-Driver and funny time displayed:
The time is: 2100.12.31 00:24:12 .
And both ([date] [time]) Files did not work.
Buy the way: How to save in the
Rootdirectory while the cam is switched off?
Greetings Holzmichel

Holzmichel (50%)
Oh, the Cam Driver is avaible now in the downloads. But no Information over the date bug with Year2100

Holzmichel (50%)
Oh Thanks, I will test the driver in the evening.
But there is no information to handle the wrong Date in the screen. The information from Dan below doesnt func. The best: delete the Date function, but how? Greetings Holzmichel

Holzmichel (50%)
Hy Guys,
now ive some answers.
First time the system would found the cam only
sometimes. The reason: the cable is defect.
With a new one there is no driver nedded for XP.

My Cam only takes a file names TIME.TXT .
I made it with the Editor and testet different
versions. Now only save
the text: 2010-03-19 17:04:00 and save the file
in the rootdirectory of the cam.
After switch off and on the cam erases
this file. The cam can placed on line,
so you can have a look if the file is erased.
You can check it with a short Video.
Switch the cam off and on is no problem but
after change the battery you can start again.
Much fun, Holzmichel.

Wayne Miller (50%)
Hi,

I put together a set of instructions from all the comments and manuals that made sense for this camera and it is here:
***********rcuniverse****/forum/m_9717174/anchors_9717174/mpage_1/key_/anchor/tm.htm#9717174

I still am not sure of how to charge from the computer, that is, should it be on or off when pluged into the USB port.

Hope the above helps.

Fly4Fun,

Wayne Miller

Wayne Miller (50%)
The Link did not store properly so here are the instructions - hope you find them useful.

MODE INSTRUCTIONS FOR HOBBY KING TURNIGY TR52DV CAMERA:

There is no Yellow or Green lights on new camera. These instructions are for cameras with the red and blue lights.

You can use either Abreviated or Detailed instructions listed below.

ABBREVIATED INSTRUCTIONS:
NOTE: MODE button is identified with M. EXECUTE or FUNCTION (Start/Stop) button is identified with a circle and square.
The mode sequence is:
Turn on SWITCH
Push Mode (M) button for voice activated video (Mode 1) - Push EXECUTE or FUNCTION to Start/Stop
Push Mode (M) again for manual activated video (Mode 2) - Push EXECUTE or FUNCTION to Start/Stop
Push Mode (M) again for picture (snapshot) (Mode 3) - Push EXECUTE or FUNCTION to take snapshot
Push Mode (M) again for voice recording (Mode 4) - Push EXECUTE or FUNCTION to Start/Stop

Holding Mode button in will turn camera off at any time (red light goes out). Do not use on/off switch before Mode button turns off camera or camera and pictures will reset.

DETAILED INSTRUCTIONS:
1. Power on.
2. Press M. Red light is on. Now the camera on in voice activated mode and will allow video recording with voice activation. Push EXECUTE or FUNCTION (Start/Stop) button identified with a circle and square to start and then stop recording.
Blue light blinks slow while recording
3. Press M again. Mode changes but light remains red. This is manual video mode. Push EXECUTE or FUNCTION (Start/Stop) button identified with a circle and square to start and then stop recording.
Blue light blinks fast while recording.
4. Press M again. Mode changes to take picture mode but light remains red. Push EXECUTE or FUNCTION (Start/Stop) button identified with a circle and square to start and then stop recording to take a picture.
Blue light blinks when picture taken
4. Press M again. Mode changes to voice recording but light is the same red. Push EXECUTE or FUNCTION (Start/Stop) button identified with a circle and square to start and then stop recording.
Blue light stays on while recording
5. Press and hold M at any time until the red light goes off to turn camera off.

NOTE: In any mode, you can start/ stop recording and then start/stop a second recording with out exiting the Mode.

NOTE: Do not turn camera switch off until you hold the MODE button and lights go off or camera will be reset and pictures will be lost.

Viewing Pictures:
With camera switch off, plug into computer with USB cable Red and Blue lights will be on. Use Windows Explorer to get pictures/audio from camera. The camera will be shown as a disk in Explorer. Look under directory DCMI and 100MEDIA for pictures

Go to Hobby King web page and read reviews for up to date information. Here is the link:
http://www.hobbycity.com/hobbycity/store/uh_viewItem.asp?idProduct=10093

Original Manual location (not for new camera):
http://www.hobbyking.com/hobbycity/store/uploads/hk52.zip

Read more: http://www.rcuniverse.com/forum/m_9717174/anchors_9717174/mpage_1/key_/anchor/tm.htm#9717174#ixzz0nIlOn5tM

2/03/2010
Dan (84%)
Sorry, my file format above is wrong. It should be:

[date]
2010.03.01
17:30:00

I tried so many different ones to get it to work, I got confused.

Don't turn that switch off!

Payment Status (32%)
Hallo, ich bin wohl zu doof. 1. Um das Datum einzustellen habe ich das Text-File erstellt und mit Leer und Return die Zeilen gewechselt. Abgelegt im Stammverzeichnis. Leider ohne Funktion. 2. Eine Treiber CD fehlte. Hier auch nicht vorhanden. Der empfohlene Treiber STK02N 2.0 von der FCO2 bringt es leider auch nicht. jedes 2. Mal heist es: Unbekanntes Gert. 3. Die Funktion als PC-Kamera funktioniert auch nicht. Da soll beim Einschalten die Mode-Taste mit gedrckt werden um in den Photomodus mit roter Anzeige zu gelangen. Das klappt gar nicht. Ob mit oder ohne gedrckte Mode-Taste beim Einschalt immer die gleiche gelbrote Anzeige. Rot immer bei USB Verbindung, Gelb bei Akkustischem VideoStandby.

Click here to see all comments